Projects and Friends

Cruising is supposed to be fun and relaxing. However, that being said boats are like houses. There is a list of improvements, maintenance, and repairs to do. As in a house, improvements can always be set aside, however maintenance and repairs must be attended to in a timely fashion because, unlike houses, boats can sink! So with old friends gone it was time to finish some boat projects. 

All that trouble for a little door latch!

One was to replace a door latch. It cost over $200 and I thought it was a direct replacement, it wasn’t! It took 5 days to install. First it had taper pins to hold the handles to the shaft instead of the normal way of set screws. I couldn’t drive the pins out with things at hand so I had to go to Home Depot to buy some pin punches to drive one pin out so I could remove one handle and install it in the latch. Then the latch was longer on the door edge then the older one, so I had to chisel out the door edge for the latch. Then there were no screws with the latch to hold it in the door, so I had to go buy wood screws to hold the latch in. Next the machine screws which go through the latch to hold on the handle plates were too long for the door. I tried to cut them, but ending up bending the screws so I bought some #8 by 32 machine screws. Well they didn’t thread into the posts on the other side of the plate. They were metric! So back to buy metric screws! Now I finally assemble the latch and handle plates and put in the handles, driving in the taper pins. Oh no! I put the handles in backward so I can’t close the door! Now I must drive a taper pin out and reverse the handles. First project is done!

The old hot water tank with all my
JB Weld trying to stop the leak

New Hot Water Tank!

Our Hot water tank has been shut off for over 2 years as it leaks and I couldn’t stop it, even after 2 tubes of JB Weld. Gene off Gewil told me Defenders was having a sale so I ordered a new tank and started to replace the old one. What a mess! It was full of water so it all had to be drained and the old fittings taken off and new fittings put on the new tank. It was an all day job and when I was done it leaked! So the next day was spent getting the system water tight. We now have hot water again! Of course we never use hot water, but it is now available.

The galley faucet leaks. We go to Home Depot and buy a new faucet that says it is for 3/8” connectors. I buy 3/8” NPT to barb connectors and go to screw them in at the boat and they don’t fit! I talk to Beagle Knot, who replaced his faucet, and find out what faucet he used. Off to Ace Hardware I go and buy the faucet. It still doesn’t screw in! Back we go to Ace and low and behold they have and adapter! We buy the adapter and the faucet is now replaced!

My new bypass system

Then it was time to put in the new hawse pipe for a second anchor on the bow. It went well. The replacement of the friction hinges for both the head hatches was an all day job. The booster pump for my water maker would always cut off with an overheating after 30 minutes of operation. My friend Gordon, on Ocean Wings, installed a water maker and when I looked at it he had a bypass valve on his booster pump to keep the pressure down. So off we went and got a valve, pressure gauge, hose and fittings. We put it together and tried it. Sure enough the booster pump was pumping at 50 psi and I could open the valve and get it down to 10 psi. However, one hose fitting was leaking. It was too small, so off we went to get another fitting! We replaced the fitting and all was well! Now the booster pump no longer cuts off.

Ready to work

Carl glasses  the keel

The dinghy was next! The dinghy always took in water in the lower hull, but when I put it up in the davits I could never see any water coming out! Also the air tubes were leaking somewhere as we have to pump it up every three days. So we took the dinghy to the beach and unloaded it and turned it upside down. We put a stripe of fiberglass down the keel, re-bed the upper drain plug, and replace and bedded the lower hull drain plug. We then soaped the bottom of the air tube looking for air leaks to no avail. When the fiberglass cured we turned the dinghy over and soaped all the top seams and could still  not find a leak. So we loaded up the dinghy to see if we did any good and the jury is still out as we kept getting rain so we can’t tell if the lower hull is still leaking or not. After 3 days the air tubes were leaking air slowly. Ugh!  Will have to readdress and see what is going on to cause the slow leaking.

All done with new drain plug

New fuel filter installed on dinghy

So as a preventative measure I went and bought a gas filter and water separator for the dinghy. Mounting the filter went well then my brain stopped working. I cut the hose and attached it to the filter without looking at the bulb pump and of course cut the hose on the wrong end of the pump. It was pumping gas from the engine to the tank! With much effort I removed the weird irremovable clamps from the bulb ends and reversed the bulb and attached it with hose clamps. I pumped up the gas and delightedly watched it fill the filter, but then it poured out of the connection between the engine and fuel hose! Back to the stores to find out Yanmar outboards must have OEM fuel fittings. So $30 poorer I go back and replace the fuel clip. Well the brain is still out to lunch and I replace the one for the tank not the engine! Arhhh! More hose clamps latter and now I replace the right one and all works. Until I put the dinghy in the davits. It sets bow up and fuel tank down and now fuel is coming out of the tank end fitting! Back down the dinghy goes and I replace it with the old engine fitting so life is good. Until I use the dinghy and realize I cut the hose from the filter to the engine too short and I can’t turn the engine all the way over! Back to the store for more hose and replace the filter to engine hose. Another job done.

Old metal clamp for stern drive

New $60 clamp!

For Maintenance every week we check the bilges and thru hulls, exercise the thru hulls, check the engine and stern drive oil levels, check the engine belts and wd40 all locks and surfaces that may rust. During that check I found the clamp for the starboard stern drive rubber seal was rusted through. So off I go to get a new one. It is a circle of thin metal that bends over itself to tighten into a seal. The cost, $60! Also to install it you must disconnect the engine from the stern drive, take out the engine mount bolts, push the engine forward to get the shaft out of the stern drive, disconnect all the transmission cables and water inlet! I bought a big hose clamp for $12 and put it around the flange.

I changed the filter to the water maker. Old is on the left

Part of the farmer's market

The market is huge!

Of course one can’t work on the boat all day every day, so during this time we went to the big farmers market and did a good deal of snorkeling.

A Flame Scallop and Arrow crab right off the beach

Bristle worm on the bottom

The Corwith Cramer an SEA ship
anchored in Brewers Bay she is
the sister ship to the Westward which
I sailed on in 1972!

It's a floating Bar!
It wasn't open as it is in the park

Peter owns the floating bar

We needed a break so we head to Maho for a week. It was a beautiful relaxing time. We were moored deep in Maho so the winds blew and we didn’t know it. The waves were high out in the ocean and we never saw them. At night the only light one could see was from other boats. We swam and snorkeled and had a very relaxing time. So while there Sue, off Oceanwings, said she would help Leslie make a template for dinghy chaps, and Gordon suggested we look for the air leak in the dinghy again. So into the beach we go and soap all the seams again to no avail. Then Gordon says, “Soap the whole boat.” So I do and low and behold we find a weeping leak and a solid leak in the fabric. I patch them that night and so far it has held.

We hike to Annenberg

Party Time!

While in Maho we did a hike to Annenberg plantation ruins and had a party on our boat with friends who were moored nearby.

After the nice time at Maho we returned to Water Island and Honeymoon beach. We saw a movie that night, but left the next morning for Brewers Bay as our anchor was not holding well. 

The little fish calls us home

I guess we haven't motored enough
These 2 goose neck barnacles call
our prop home

Now we are preparing the boat for a visit from Leslie’s sister Ally from Wyoming.